Temp

Software Updates
sudo apt-get update
sudo apt-get upgrade
sudo shutdown -r now

Firmware Update
sudo apt-get install rpi-update
sudo rpi-update
sudo shutdown -r now

WLAN
http://www.psychicorigami.com/2013/01/27/configuring-an-edimax-ew-7811un-on-a-raspberry-pi-for-wifi/
sudo iwlist wlan0 scanning
sudo nano /etc/network/interfaces
auto wlan0
iface wlan0 inet dhcp
wpa-conf /etc/wpa.conf

echo $(wpa_passphrase ssid networkpassword) | sudo tee /etc/wpa.conf
sudo nano /etc/wpa.conf

network={
ssid=”
#psk=”
psk=
}
sudo ifup wlan0

Dependencies
sudo apt-get install -y libjpeg62 libjpeg62-dev libavformat53 libavformat-dev libavcodec53 libavcodec-dev libavutil51 libavutil-dev libc6-dev zlib1g-dev libmysqlclient18 libmysqlclient-dev libpq5 libpq-dev

Network Share
sudo nano

UV4L
add in /etc/apt/sources.list:
deb http://www.linux-projects.org/listing/uv4l_repo/raspbian/ wheezy main

sudo wget http://www.linux-projects.org/listing/uv4l_repo/lrkey.asc && sudo apt-key add ./lrkey.asc
sudo apt-get update
sudo apt-get install uv4l uv4l-raspicam
sudo apt-get install uv4l-raspicam-extras

Motion Software, Installation
sudo apt-get install motion
sudo apt-get install libjpeg62

cd ~/
mkdir mmal
cd mmal
wget https://www.dropbox.com/s/xdfcxm5hu71s97d/motion-mmal.tar.gz
tar -zxvf motion-mmal.tar.gz

Motion Software, Configuration
nano motion-mmalcam.conf
width
height
target_dir
output_pictures
text _left
logfile
search for them in turn using ctrl+w and set them as follows

width 640
height 480
target_dir /home/pi/m-video
output_pictures off
text_left Pi-cam %t
logfile /home/pi/mmal/motion.log

sudo LD_PRELOAD=/usr/lib/uv4l/uv4lext/armv6l/libuv4lext.so motion

http://192.168.x.x:8081

raspivid -w 640 -h 480 -fps 90 -t 10000 -o test90fps.h264
raspivid -w 1920 -h 1080 -fps 30 -t 1000000 -o test_1920x1080_30fps.h264

Cron Reboot
sudo crontab -e
0 0 * * * /sbin/shutdown -r

http://rbnrpi.wordpress.com/project-list/setting-up-wireless-motion-detect-cam/
http://www.psychicorigami.com/2013/01/27/configuring-an-edimax-ew-7811un-on-a-raspberry-pi-for-wifi/
http://babaawesam.com/2014/03/24/shooting-slow-motion-videos-using-raspberry-pi-camera/

To add remote workgroup servers to Server Manager

On the computer that is running Server Manager, add the workgroup server name to the TrustedHosts list. This is a requirement of NTLM authentication. To add a computer name to an existing list of trusted hosts, add the Concatenate parameter to the command. For example, to add the Server01 computer to an existing list of trusted hosts, use the following command.
Copy

Set-Item wsman:\localhost\Client\TrustedHosts Server01 -Concatenate -Force

Determine whether the workgroup server that you want to manage is in the same subnet as the computer on which you are running Server Manager.

If the two computers are in the same subnet, or if the workgroup server’s network profile is set to Private in the Network and Sharing Center, go on to the next step.

If they are not in the same subnet, or if the workgroup server’s network profile is not set to Private, on the workgroup server, change the inbound Windows Remote Management (HTTP-In) setting in Windows Firewall to explicitly allow connections from remote computers by adding the computer names on the Computers tab of the setting’s Properties dialog box.
securitySecurity Note
Running the cmdlet in this step overrides User Account Control (UAC) measures that prevent elevated processes from running on workgroup computers unless the built-in Administrator or the System account is running the processes. The cmdlet lets members of the Administrators group manage the workgroup server without logging on as the built-in Administrator. Allowing additional users to manage the workgroup server can reduce its security; however, this is more secure than providing built-in Administrator account credentials to what might be multiple people who are managing the workgroup server.

To override UAC restrictions on running elevated processes on workgroup computers, create a registry entry called LocalAccountTokenFilterPolicy on the workgroup server by running the following cmdlet.
Copy

New-ItemProperty -Name LocalAccountTokenFilterPolicy -path HKLM:\SOFTWARE\Microsoft\Windows\CurrentVersion\Policies\System -propertyType DWord -value 1

On the computer on which you are running Server Manager, open the All Servers page.

If the computer that is running Server Manager and the target workgroup server are in the same workgroup, skip to the last step. If the two computers are not in the same workgroup, right-click the target workgroup server in the Servers tile, and then click Manage as.

Log on to the workgroup server by using the built-in Administrator account for the workgroup server.

Verify that Server Manager is able to connect to and collect data from the workgroup server by refreshing the All Servers page, and then viewing the manageability status for the workgroup server.

To add remote servers when Server Manager is running on a workgroup computer

On the computer that is running Server Manager, add remote servers to the local computer’s TrustedHosts list in a Windows PowerShell session. To add a computer name to an existing list of trusted hosts, add the Concatenate parameter to the command. For example, to add the Server01 computer to an existing list of trusted hosts, use the following command.
Copy

Set-Item wsman:\localhost\Client\TrustedHosts Server01 -Concatenate -Force

Determine whether the server that you want to manage is in the same subnet as the workgroup computer on which you are running Server Manager.

If the two computers are in the same subnet, or if the workgroup computer’s network profile is set to

Private in the Network and Sharing Center, go on to the next step.

If they are not in the same subnet, or if the workgroup computer’s network profile is not set to Private, on the workgroup computer that is running Server Manager, change the inbound Windows Remote Management (HTTP-In) setting in Windows Firewall to explicitly allow connections from remote computers by adding the computer names on the Computers tab of the setting’s Properties dialog box.

On the computer on which you are running Server Manager, open the All Servers page.

Verify that Server Manager is able to connect to and collect data from the remote server by refreshing the All Servers page, and then viewing the manageability status for the remote server. If the Servers tile still displays a manageability error for the remote server, go on to the next step.

Log off of the computer on which you are running Server Manager, and then log on again by using the built-in Administrator account. Repeat the preceding step, to verify that Server Manager is able to connect to and collect data from the remote server.

If you have followed the procedures in this section, and you continue to have problems managing workgroup computers, or managing other computers from workgroup computers, see about_Remote_Troubleshooting on the Microsoft website.

Refer to: Add Servers to Server Manager

http://technet.microsoft.com/en-us/library/hh831453.aspx

Set-Item WSMan:\localhost\Client\TrustedHosts -Value -Concatenate, where RemoteServerName is the name of the computer running Hyper-V Server that you want to manage.

  • Installing drivers on HyperV Server 2012 R2
    pnputil -i -a *.inf
  • PowerShell: Disable HYperV Services on Windows HyperV Server 2012 R2″
    Set-Service vmicheartbeat -StartupType Disabled
    Set-Service vmickvpexchange -StartupType Disabled
    Set-Service vmicrdv -StartupType Disabled
    Set-Service vmicshutdown -StartupType Disabled
    Set-Service vmictimesync -StartupType Disabled
    Set-Service vmicvss -StartupType Disabled
    Set-Service vmms -StartupType Disabled
  • PowerShell Execution Policy unrestricted
    Set-ExecutionPolicy Unrestricted
  • Windows Firewall deactivate
    netsh advfirewall set allprofiles state off
  • Change RDP listening port
    /support.microsoft.com/kb/306759/en
  • Add additional RDP listening port
    www.dell.com/support/troubleshooting/ag/en/agdhs1/KCS/KcsArticles/ArticleView?c=ag&l=en&s=dhs&docid=630531
  • Windows Server 2012 R2: Storage Pool anlegen
    Get-PhysicalDisk
    $disks = Get-PhysicalDisk |? {$_.CanPool -eq $true}
    New-StoragePool -StorageSubSystemFriendlyName *Spaces* -FriendlyName TieredPool -PhysicalDisks $disks
    Get-StoragePool -FriendlyName TieredPool | Get-PhysicalDisk | Select FriendlyName, MediaType
    Set-PhysicalDisk -FriendlyName PhysicalDisk1 -MediaType SSD
    Set-PhysicalDisk -FriendlyName PhysicalDisk5 -MediaType SSD
    Set-PhysicalDisk -FriendlyName PhysicalDisk6 -MediaType SSD
    Set-PhysicalDisk -FriendlyName PhysicalDisk2 -MediaType HDD
    Set-PhysicalDisk -FriendlyName PhysicalDisk3 -MediaType HDD
    Set-PhysicalDisk -FriendlyName PhysicalDisk4 -MediaType HDD
    $ssd_tier = New-StorageTier -StoragePoolFriendlyName TieredPool -FriendlyName SSD_Tier -MediaType SSD
    $hdd_tier = New-StorageTier -StoragePoolFriendlyName TieredPool -FriendlyName HDD_Tier -MediaType HDD
    $vd1 = New-VirtualDisk -StoragePoolFriendlyName TieredPool -FriendlyName VirtualMachines -StorageTiers @($ssd_tier, $hdd_tier) -StorageTierSizes @(30GB, 1.1TB) -ResiliencySettingName Mirror -WriteCacheSize 5GB
    $vd2 = New-VirtualDisk -StoragePoolFriendlyName TieredPool -FriendlyName HD -Size 30TB -ResiliencySettingName Parity -ProvisioningType Thin -WriteCacheSize 20GB
    Set-VirtualDisk -FriendlyName HD -WriteCacheSize 21GB
  • c:\$extend
    fsutil usn deletejournal /D C
    cleanmgr sageset:11
    cleanmgr sagerun:11

    http://wiki.cyanogenmod.org/w/Ovation_Info

    IMEI *#06#
    Hidden Menu *#0* #

    net user marco /add
    Net localgroup Administrators /add marco

    net use p: \\200.200.200.50\pool-data
    c:\program files (x86)\Squeezebox\server\squeezeboxcp.exe

    netsh firewall set portopening protocol = TCP port = 9000 name = squeezebox mode = ENABLE scope = SUBNET profile = CURRENT

    In den Squeezebox Server Einstellungen:
    \\lanthan\music

    http://yagyagaire.blogspot.de/2011/09/how-to-partition-sd-card-and-install.html#.UY1ne7Xxrfw

    Turn of thumbbs.db generation
    Fortunately, there’s an easy way to prevent further Thumbs.db hassle:

    Ensure you’re logged in using an administrator account.
    Hit Win+R, type gpedit.msc in the Run window and click OK. The Local Group Policy Editor will be launched.
    Navigate through the tree to User Configuration > Administrative Templates > Windows Components > then either Windows Explorer (Windows Vista/7) or File Explorer (Windows 8).
    Local Group Policy Editor

    In the right-hand pane, double-click “Turn off the caching of thumbnails in hidden thumbs.db files”.
    Select Enabled (don’t make my mistake of choosing “Disabled” — you’re enabling the switching off of Thumbs.db. Not particularly intuitive, Microsoft!)

    HyperV Server 2012 R2 manage
    netsh firewall set service fileandprint

    i8kfangui sign driver under win7x64

    1. Install i8kfangui 3.1 (with disabling driver signature enforcement), do not restart yet.
    2. Download and install Driver Signature Enforcement Overrider 1.3b
    http://www.ngohq.com/home.php?page=Files&go=cat&dwn_cat_id=34
    3. Select sign, and paste path to fanio.sys (I found 2 fanio.sys in my Windows directory. One in Windows\system32\drivers\fanio.sys and one in Windows\SystemWOW64\drivers\fanio.sys) I signed both
    4. Select test mode
    5. Reboot

    http://www.dtdns.org

    Update-URL: http://www.dtdns.com/autodns.cfm?id=hostname.domain.net&pw=password&client=fritzbox

    Fritzbox – Einstellungen – Freigaben Dynamic DNS

    Über Dynamic DNS können Anwendungen und Dienste, für die in der FRITZ!Box-Firewall Portfreigaben eingerichtet wurden, unter einem festen Domainnamen aus dem Internet erreicht werden, obwohl sich die öffentliche IP-Adresse der FRITZ!Box mit jeder Interneteinwahl ändert.

    [x] Dynamic DNS benutzen

    Geben Sie die Anmeldedaten für Ihren Dynamic DNS-Anbieter an.

    Dynamic DNS-Anbieter Benutzerdefiniert
    Update-URL
    www.dtdns.com/autodns.cfm?id=&pw=&client=

    Domainname hostname.domain.net
    Benutzername fritzbox
    Kennwort ******
    Kennwortbestätigung
    ******

    Die Fritzbox unterstützt die Verwendung von Variablen

    Domainname =
    Benutzername =
    Kennwort =

    Variablen müssen in spitze Klammern (Kleiner als und Größer als-Zeichen) gesetzt werden.

    Hinweis für mich:

    Leider kann ich diese Sonderzeichen hier mit Jommla nicht immer richtig darstellen.Dazu benötigt man das Backend.

    Set password expiry for user account:
    WMIC USERACCOUNT WHERE “Name=’username'” SET PasswordExpires=FALSE

    o F2 boot to BIOS.
    o F12 boot device menu.
    0 Fn+F1 sleep/hibernate per power management setting.
    o Fn+F2 battery charger ON/OFF.
    o Fn+F3 DCP Power Manager Battery Status.
    o Fn+F4 numlock ON/OFF for embedded Fn+numeric keypad.
    o Fn_F5 scroll lock ON/OFF.
    o Fn+F7 DCP.
    o Fn+F8 display device.
    o Fn+D display OFF/ON (conserve battery without shutting down entire system).
    o Fn+Z reset fan temperature table and sensor.
    o Fn+Right-Arrow keyboard illumination OFF/ON Auto ALS (lit upon input in dim lighting)/ON (lit upon input). Use DCP to set input device, brightness, and auto OFF delay.
    o Fn+Left-Arrow display Ambient Light Sensor OFF/ON (brightness varies with ambient lighting).
    o Fn+Up/Dn-Arrows override display brightness until boot to BIOS setting and/or power mananagement setting.
    o Alt+Fn+F11 screen shot.